Knowledge Base Archives: S1

S1 Service Instructions

S1: Tank Reseal

Please handle the tank carefully, as cracking either the top or bottom half would cause irreparable damage. If your tank has any cracks, you will need to replace it (WaterRower Part # WRPT004). Please read all instructions carefully before beginning any WaterRower service actions. Please view the WaterRower tank repair video at: http://www.waterrowerservice.com/videos We highly …

S1 Service Instructions

S1: Top Deck Replacement

For Video Instructions, click here: Removing the Top Deck Step 1- Remove the handle from the handle rests and place the handle in the full forward position as shown.   Step 2- Stand the WaterRower upright and disconnect the bungee as shown. Step 3- Lay the WaterRower down. Remove the Tie Rods and JCB bolts …

S1 Service Instructions

S1: Recoil Bushing Replacement

Handle Removal Step 1- Remove the handle from the Handle rests and place the Handle in the full forward position.   Step 2- Stand the WaterRower upright and disconnect the bungee from the Recoil Belt as shown.   Step 3- Lay the WaterRower down and slowly pull the handle so that the Drive Strap unwinds …

S1 Service Instructions

S1: Oilite Bearing Replacement

Step 1- Remove the Handle from the handle rests and place the handle in the full forward position. Step 2- Stand the WaterRower upright and disconnect the bungee from the Recoil Belt as shown.   Step 3- Lay the WaterRower down and slowly pull the handle so that the Drive Strap unwinds from the clutch …

S1 Service Instructions

S1: Level Gauge Location

The Level Gauge sticker on all Series 4 (S4) model WaterRower units, is located on the side of the tank under the tank stopper. The Level Gauge sticker on the A1 and Indo-Row units is located on the bottom of the tank. On the A1 and GX WaterRower units, this sticker also has the unit’s …

S1 Service Instructions

S1: Recoil Belt Buckle Replacement

Step 1- Pass the Recoil Belt through the bungee buckle with the belt facing the serrations on the buckle as shown. Step 2- Pass the Recoil Belt through the D-ring and back through the bungee buckle as shown. The Recoil Belt should follow itself back through the buckle. It is advised that the loose end …

S1 Service Instructions

S1: Recoil Belt Replacement (Clip On Recoil)

For Video Instructions, click here: Replacing the Recoil Belt Step 1- Remove the handle from the handle rests and place the handle in the full forward position Step 2- Stand the WaterRower upright and disconnect the bungee from the recoil belt as shown Step 3- Lay the machine down and remove the recoil strap from …

S1 Service Instructions

S1: Handle Replacement (metal clutch)

For Video Instructions, click here: Replacing the Handle Assembly (Metal/Velcro attachment) Step 1- Remove the Handle from the handle rests and place the handle in the full forward position Step 2- Stand the WaterRower upright and disconnect the bungee from the recoil belt as shown. Step 3- Lay the WaterRower down and slowly pull the …

S1 Service Instructions

S1: Handle Replacement (plastic clutch)

For Video Instructions, click here: Replacing the Handle Assembly (Plastic – Bolt On)   Step 1- Remove the handle from the handle rests and place it in the full forward position.   Step 2- Stand the WaterRower upright and unclip the bungee from the recoil belt.   Step 3- Lay the WaterRower down and slowly …

S1 Service Instructions

S1: Short Tank Assembly Replacement

Step 1. Remove the handle from the handle rests and place in the full forward position. Step 2. Stand the WaterRower upright and disconnect the bungee. Step 3. Lay the WaterRower down and pull the handle so the drive strap unwinds from the clutch housing. Remove the handle and drive strap from the clutch by unstrapping the …